 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| data modul ag - www.data-modul.com specification 20.3cm (8.0") tft rev. 01, september 2009 note: this specification is subject to change without prior notice L5S30978
revision history product number rev. revised item date L5S30978p00 00 initial issue jul .10, 2009 L5S30978p00 01 4.2 characteristics of led and led driving (page:15/43) -?forward current? and ?life time? items are added. -a graph of ?ambient temper ature vs. allowable forward current? is deleted. -note2, note3 and note4 are added. 6.2.1 application scope (page:31/43) - note is added. ( viewing area = bezel opening area) sep .08, 2009 data modul ag - www.data-modul.com 2 contents epson imaging devices corp. 1 basic specif icatio ns ........................................................................................................... .......................... 1 1.1 struct ure...................................................................................................................... ............................. 1 1.2 mechanical drawi ng........................................................................................................................ ....... 1 1.3 block diagram ........................................................................................................................ ................... 2 1.4 i/o terminals...................................................................................................................... ......................... 3 1.5 lighting system ........................................................................................................................................ 5 2 functio ns ...................................................................................................................... ..................................... 6 2.1 overview ....................................................................................................................... .............................. 6 2.2 rgb interf ace............................................................................................................................................ 6 2.3 serial interf ace....................................................................................................................................... 8 2.4 command set ............................................................................................................................ ................ 10 2.5 command descript ion .................................................................................................................... ...... 10 3 absolute maxi mum rat ings ....................................................................................................... ............... 14 3.1 absolute maximum rating ................................................................................................................... 14 4 electrical spec ificat ion ....................................................................................................... ................... 14 4.1 dc character istics................................................................................................................ ............... 14 4.2 characteristics of led and led driving ....................................................................................... 15 4.3 ac character istics................................................................................................................ ............... 16 4.4 power modes .......................................................................................................................... ................. 21 4.5 power functio ns ...................................................................................................................... ............. 22 4.6 recommended sequence ..................................................................................................................... 24 5 optical specif ication .......................................................................................................... ....................... 27 5.1 optical character istics ................................................................................................................ .... 27 5.2 definition and condition of optical characteris tics ........................................................... 27 6 inspection st andard ............................................................................................................ ....................... 30 6.1 quality standa rd....................................................................................................................... ............ 30 6.2 appearance standa rd ....................................................................................................................... .. 31 6.3 warrant y ....................................................................................................................... ........................... 33 7 reliabi lity.................................................................................................................... .................................... 34 7.1 standard test item and conditon / method ................................................................................ 34 7.2 failure judgment standa rd .............................................................................................................. 35 data modul ag - www.data-modul.com 3 contents epson imaging devices corp. 8 packi ng ........................................................................................................................ ..................................... 36 9 lcd module usage and precaut ions............................................................................................... ..... 39 9.1 handlin g ....................................................................................................................... ............................. 39 9.2 design ......................................................................................................................... ................................ 40 9.3 storage ........................................................................................................................ ............................. 43 9.4 disposal....................................................................................................................... .............................. 43 9.5 other precauti ons .................................................................................................................... ........... 43 data modul ag - www.data-modul.com 4 product number L5S30978p00 revision number 01 page epson imaging devices corp. 1 basic specifications this document gives the characteristics of the active matrix 8.0 inch tft lcd. 1.1 structure no. factor specifications unit remarks 1 lcd structure a-tft lcd - 2 module size (w x h x t) 187.5(w) x 120(h) x 9.9(t) mm note1) 3 weight 270 g 4 active area (w x h) 174.0(w) x 104.4(h) mm 5 screen size 8.0 inch - 6 number of dots 800 x rgb (w) x 480 (h) - 7 dot pitch (horizontal x vertical) 0.2175(w) x 0.2175(h) mm 8 dot layout rgb stripe - 9 liquid crystal mode vistarich technology normally black transmissive type - 10 polarization plate hard coat - 11 operating temperature - 30 to +85 deg. c 12 storage temperature - 40 to +90 deg. c note1) the module size(w) doesn?t contain the fixing boss. 1.2 mechanical drawing please refer to the outline drawing (p068887-11-00) of this lcd module. data modul ag - www.data-modul.com 5 product number L5S30978p00 revision number 01 page epson imaging devices corp. 1.3 block diagram 3 ( # y 3 ( # y 7 b m j e e p u t 7 b m j e e p u t source driver source driver gate driver gate driver op-amp pclk vs hs r [5:0] g [5:0] b [5:0] vdd gnd scl sda xcs xres eeprom vcom cn1 anode1 cathode1 anode2 cathode2 anode3 cathode3 anode4 cathode4 cn2 back light unit data modul ag - www.data-modul.com 6 product number L5S30978p00 revision number 01 page epson imaging devices corp. 1.4 i/o terminals cn1: display interface pin assignment (50pin) ; suitable connector : iriso / 9686 (au-plating) pin no. symbol function i/o remarks 1 gnd ground p 2 gnd ground p 3 r[0] display data (red) i (lsb) 4 r[1] display data (red) i 5 r[2] display data (red) i 6 r[3] display data (red) i 7 r[4] display data (red) i 8 r[5] display data (red) i (msb) 9 gnd ground p 10 gnd ground p 11 gnd ground p 12 g[0] display data (green) i (lsb) 13 g[1] display data (green) i 14 g[2] display data (green) i 15 g[3] display data (green) i 16 g[4] display data (green) i 17 g[5] display data (green) i (msb) 18 gnd ground p 19 gnd ground p 20 gnd ground p 21 b[0] display data (blue) i (lsb) 22 b[1] display data (blue) i 23 b[2] display data (blue) i 24 b[3] display data (blue) i 25 b[4] display data (blue) i 26 b[5] display data (blue) i (msb) 27 gnd ground p 28 gnd ground p 29 gnd ground p 30 gnd ground p data modul ag - www.data-modul.com 7 product number L5S30978p00 revision number 01 page epson imaging devices corp. 31 pclk clock for display data i latched at rising edge 32 gnd ground p 33 gnd ground p 34 vs vertical synchronous signal i ?l? active 35 gnd ground p 36 gnd ground p 37 gnd ground p 38 hs horizontal synchronous signal i ?l? active 39 gnd ground p 40 vdd power supply p 41 vdd power supply p 42 gnd ground p 43 gnd ground p 44 xres reset i ?l? active 45 gnd ground p 46 xcs chip select for serial data i ?l? active 47 scl serial clock i latched at rising edge 48 sda serial data i 49 sda serial data i 50 gnd ground p cn2 : backlight interface pin assignment (8pin) ; suitable connector : iriso / 9686 (au-plating) pin no. symbol function i/o description 1 anode1 led anode terminal1 p 2 cathode 1 led cathode terminal1 p 3 anode 2 led anode terminal 2 p 4 cathode 2 led cathode terminal2 p 5 anode 3 led anode terminal3 p 6 cathode 3 led cathode terminal3 p 7 anode 4 led anode terminal4 p 8 cathode 4 led cathode terminal4 p i/o : input / output terminal, i : input terminal, o : output terminal, p : power line terminal data modul ag - www.data-modul.com 8 product number L5S30978p00 revision number 01 page epson imaging devices corp. 1.5 lighting system led type for lighting items description led type ns2w123 color rank a93,a94a,b91,b92a,b93,b94a luminous intensity rank pv5, pv6, pv7 anode 1 cathode 2 led 6p cathode 1 pin 1 2 3 4 6 led schematic 7 8 anode 2 anode 3 cathode 3 anode 4 cathode 4 led 6p led 6p led 6p 5 data modul ag - www.data-modul.com 9 product number L5S30978p00 revision number 01 page epson imaging devices corp. 2 functions 2.1 overview this lcd module has two types of used for transferring of command and pixel data. 1) rgb interface 18bit parallel bus for transferring of pixel data. 2) serial interface 3 wire serial bus for transferring of commands. 2.2 rgb interface 2.2.1 general description for rgb interface pixel clock (pclk) is running all the time without stopping in normal mode and it is used for entering hs, vs and r[5:0],g[5:0] ,b[5:0] lines states on a rising edge of the pclk. vertical synchronization (vs) informs when a new frame starts. this signal is active low and its state is read to the display module on a rising edge of the pclk-line. horizontal synchronization (hs) informs when a new line starts. this signal is active low and its state is read to the display module on a rising edge of the pclk-line. r[5:0],g[5:0] ,b[5:0] consist image information that is transferred on the displa y. r[5:0],g[5:0] ,b[5:0] lines can be ?0? or ?1?. these lines ar e read on a rising edge of the pclk-line. the pixel clock cycle is described in the following figure. pclk hs vs r[5:0] g[5:0] b[5:0] host changes r[5:0],g[5:0],b[5:0],hs and vs lines when there is a falling edge of the pclk display reads r[5:0],g[5:0],b[5:0],hs and vs lines when there is a rising edge of the pclk data modul ag - www.data-modul.com 10 product number L5S30978p00 revision number 01 page epson imaging devices corp. 2.2.2 18-bit color order of rgb interface xres b2 b3 b ( 0 , 0 ) bit3 pclk 3 ( # 3 ( # 3 ( # pixels on the display vs hs 4 b ( 1 , 0 ) bit3 b ( 2 , 0 ) bit3 b ( 3 , 0 ) bit3 b ( 4 , 0 ) bit3 b ( 0 , 0 ) bit2 b ( 1 , 0 ) bit2 b ( 2 , 0 ) bit2 b ( 3 , 0 ) bit2 b ( 4 , 0 ) bit2 b0 b1 b ( 0 , 0 ) bit1 b ( 1 , 0 ) bit1 b ( 2 , 0 ) bit1 b ( 3 , 0 ) bit1 b ( 4 , 0 ) bit1 b ( 0 , 0 ) bit0 b ( 1 , 0 ) bit0 b ( 2 , 0 ) bit0 b ( 3 , 0 ) bit0 b ( 4 , 0 ) bit0 b4 b5 b ( 0 , 0 ) bit5 b ( 1 , 0 ) bit5 b ( 2 , 0 ) bit5 b ( 3 , 0 ) bit5 b ( 4 , 0 ) bit5 b ( 0 , 0 ) bit4 b ( 1 , 0 ) bit4 b ( 2 , 0 ) bit4 b ( 3 , 0 ) bit4 b ( 4 , 0 ) bit4 g2 g3 g ( 0 , 0 ) bit3 g ( 1 , 0 ) bit3 g ( 2 , 0 ) bit3 g ( 3 , 0 ) bit3 g ( 4 , 0 ) bit3 g ( 0 , 0 ) bit2 g ( 1 , 0 ) bit2 g ( 2 , 0 ) bit2 g ( 3 , 0 ) bit2 g ( 4 , 0 ) bit2 g0 g1 g ( 0 , 0 ) bit1 g ( 1 , 0 ) bit1 g ( 2 , 0 ) bit1 g ( 3 , 0 ) bit1 g ( 4 , 0 ) bit1 g ( 0 , 0 ) bit0 g ( 1 , 0 ) bit0 g ( 2 , 0 ) bit0 g ( 3 , 0 ) bit0 g ( 4 , 0 ) bit0 g4 g5 g ( 0 , 0 ) bit5 g ( 1 , 0 ) bit5 g ( 2 , 0 ) bit5 g ( 3 , 0 ) bit5 g ( 4 , 0 ) bit5 g ( 0 , 0 ) bit4 g ( 1 , 0 ) bit4 g ( 2 , 0 ) bit4 g ( 3 , 0 ) bit4 g ( 4 , 0 ) bit4 r2 r3 r ( 0 , 0 ) bit3 r ( 1 , 0 ) bit3 r ( 2 , 0 ) bit3 r ( 3 , 0 ) bit3 r ( 4 , 0 ) bit3 r ( 0 , 0 ) bit2 r ( 1 , 0 ) bit2 r ( 2 , 0 ) bit2 r ( 3 , 0 ) bit2 r ( 4 , 0 ) bit2 r0 r1 r ( 0 , 0 ) bit1 r ( 1 , 0 ) bit1 r ( 2 , 0 ) bit1 r ( 3 , 0 ) bit1 r ( 4 , 0 ) bit1 r ( 0 , 0 ) bit0 r ( 1 , 0 ) bit0 r ( 2 , 0 ) bit0 r ( 3 , 0 ) bit0 r ( 4 , 0 ) bit0 r4 r5 r ( 0 , 0 ) bit5 r ( 1 , 0 ) bit5 r ( 2 , 0 ) bit5 r ( 3 , 0 ) bit5 r ( 4 , 0 ) bit5 r ( 0 , 0 ) bit4 r ( 1 , 0 ) bit4 r ( 2 , 0 ) bit4 r ( 3 , 0 ) bit4 r ( 4 , 0 ) bit4 data modul ag - www.data-modul.com 11 product number L5S30978p00 revision number 01 page epson imaging devices corp. 2.3 serial interface 2.3.1 general description the display module uses 3-wire 9-bit serial interf ace, which is used as command interface. the chip select, xcs (active low) enables and disables the serial interface. xres (active low) is external reset signal. scl is the serial data clock and sda is serial data. serial data is input to sda in the sequence d/xc, d7 to d0. the display module reads the data at the rising edge of scl signal. the first bit of serial data, d/xc, is data/command flag. when d/xc = ?1?, d7 to d0 bits are command parameter. when d/xc = ?0?, d7 to d0 bits compose a command. 2.3.2 command write the host cpu drives the xcs pin low and starts by setting the d/xc-bit on sda . the bit is read by the display at the first rising edge of scl. at the next falling edge of scl the msb data bit (d7) is set on sda by the cpu. at the next falling edge of scl the next bit (d6) is set on sda . this continues until all 8 data bits have been transmitted as shown in the following figure. 0d7 d1 d2 d3d4d5d6 d0 d0 d/xc d7 d6 d5 d4 d3 d2 d1 command command or parameter xcs sda scl host 2.3.3 display module data transfer recovery if there is a break in data transmission while transferring command, image data or multiple parameters before a whole byte has been completed, the display modul e must reset the interface in a way that it will be ready to receive the same byte re-transmitted when the chip select line (xcs) is next activated. see the following example in the following figure. d/xc d7 d4d5 d6 d0 d/xc d7 d6 d5 d4 d3 d2 d1 command/parameter command or parameter xcs sda scl host break if one or more parameter command is being sent and a break occurs while sending any parameter before the last one and if the host then sends a new command rather than re-transmitting the parameter that was interrupted, then the par ameters that were successfully sent are stored and the parameter where the break occurred is rejected. the interf ace is ready to receive next byte as shown: command break command parameter 2 parameter 1 data modul ag - www.data-modul.com 12 product number L5S30978p00 revision number 01 page epson imaging devices corp. 2.3.4 display module data transfer pause it will be possible when transferring image data, command or multiple parameter data to invoke a pause in the data transmission. if the chip select line is released after a whole byte of image data, command or multiple parameter data has been completed, then t he display module will wait and continue command or parameter data transmission from the point w here it was paused as shown below figure. d4 d3 d0d1d2 d0 d/xc d7 d6 d5 d4 d3 d2 d1 command/parameter command or parameter xcs sda scl host pause there are 4 cases when this kind of pause is possible: 1) command ? pause ? command 2) command ? pause ? parameter 3) parameter ? pause ? command 4) parameter ? pause ? parameter data modul ag - www.data-modul.com 13 product number L5S30978p00 revision number 01 page epson imaging devices corp. 2.4 command set note 1: undefined commands are working as a nop (00h) command. note 2: commands 10h, 13h, 28h, 29h, and 36h are updated during vs when the display module is in display on mode to avoid abnormal visual effects. during sleep mode, these commands are updated immediately. 2.5 command description 2.5.1 no operation (00h) 00h nop (no operation) d/xc d7 d6 d5 d4 d3 d2 d1 d0 hex command 0 0 0 0 0 0 0 0 0 00 parameter no parameter description this command is an empty command. it does not have any effect on the display module. 2.5.2 software reset (01h) 01h swreset (software reset) d/xc d7 d6 d5 d4 d3 d2 d1 d0 hex command 0 0 0 0 0 0 0 0 1 01 parameter no parameter description this command resets lcd module by software. restriction s it is necessary to wait 5 ms before s ending new command following software reset. if sw reset is applied during display on mode, it is necessary to wait 120ms before sending slpout command. no. command hex d7 d6 d5 d4 d3 d2 d1 d0 functions 1 nop 00 0 0 0 0 0 0 0 0 no operation 2 swreset 01 0 0 0 0 0 0 0 1 software reset 3 slpin 10 0 0 0 1 0 0 0 0 sleep state 4 slpout 11 0 0 0 1 0 0 0 1 sleep state release 5 noron 13 0 0 0 1 0 0 1 1 test mode release 6 disoff 28 0 0 1 0 1 0 0 0 display off 7 dison 29 0 0 1 0 1 0 0 1 display on madctl 36 0 0 1 1 0 1 1 0 memory access control 8 parameter 1 00 b7 b6 0 0 0 0 0 0 scanning direction of the panel colmod 3a 0 0 1 1 1 0 1 0 i/f color format setting 9 parameter 1 60 0 1 1 0 0 0 0 0 262k colors data modul ag - www.data-modul.com 14 product number L5S30978p00 revision number 01 page epson imaging devices corp. 2.5.3 sleep in (10h) 10h slpin (sleep in) d/xc d7 d6 d5 d4 d3 d2 d1 d0 hex command 0 0 0 0 1 0 0 0 0 10 parameter no parameter description this command sets the sleep state of the lcd module. restrictions this command has no effect when modul e is already in sleep mode. it is necessary to wait 5 ms before sending next command. and it is necessary to wait 120 ms after sending slpout command (when in sleep mode) before slpin command can be sent. 2.5.4 sleep out (11h) 11h slpout (sleep out) d/xc d7 d6 d5 d4 d3 d2 d1 d0 hex command 0 0 0 0 1 0 0 0 1 11 parameter no parameter description this command turns off sleep mode. in this mode the dc/dc converter is enabled and panel scanning is started. restriction s this command has no effect when module is already in display on mode. it is necessary to wait 5 ms before sending next command. and it is necessary to wait 120 ms after sending slpin command (when in display on mode) before slpout command can be sent. 2.5.5 normal mode on (13h) 13h noron (normal mode on) d/xc d7 d6 d5 d4 d3 d2 d1 d0 hex command 0 0 0 0 1 0 0 1 1 13 parameter no parameter description this command returns the display to normal mode. this command turns test mode off. data modul ag - www.data-modul.com 15 product number L5S30978p00 revision number 01 page epson imaging devices corp. 2.5.6 display off (28h) 28h disoff (display off) d/xc d7 d6 d5 d4 d3 d2 d1 d0 hex command 0 0 0 1 0 1 0 0 0 28 parameter no parameter description this command turns off the display. the output from rgb i/f is disabled and blank page inserted. 2.5.7 display on (29h) 29h dion (display on) d/xc d7 d6 d5 d4 d3 d2 d1 d0 hex command 0 0 0 1 0 1 0 0 1 29 parameter no parameter description this command turns on the display. it is used to recover from disoff command. output from the rgb i/f to panel is enabled. data modul ag - www.data-modul.com 16 product number L5S30978p00 revision number 01 page epson imaging devices corp. 2.5.8 memory access control (36h) 36h madctl (memory access control) d/xc d7 d6 d5 d4 d3 d2 d1 d0 hex command 0 0 0 1 1 0 1 1 0 36 1st parameter 1 b7 b6 0 0 0 0 0 0 xx description this command defines the scanning direction of the panel. bit name description b7 page address order b6 column address order b7 and b6 control the scanning direction of the panel. 2.5.9 interface color format (3ah) 3ah colmod (interface color format) d/xc d7 d6 d5 d4 d3 d2 d1 d0 hex command 0 0 0 1 1 1 0 1 0 3a 1st parameter 1 0 1 1 0 0 0 0 0 60 description this command defines the format of rgb image data, which is transferred via rgb i/f. this command is used for refresh sequence. b7 = 0 and b6 = 0 b7 = 0 and b6 = 1 b7 = 1 and b6 = 0 start point (0, 479) b7 = 1 and b6 = 1 start point (799, 479) end point (0, 479) end point (799, 479) start point (799, 0) start point (0, 0) end point (0, 0) end point (799, 0) data modul ag - www.data-modul.com 17 product number L5S30978p00 revision number 01 page epson imaging devices corp. 3 absolute maximum ratings 3.1 absolute maximum rating lcd module parameter symbol rating unit power supply voltage vdd -0.3 to +4.2 v logic signal input voltage vi -0.3 to vdd+0.3 v logic signal output voltage vo -0.3 to vdd+0.3 v note: ta = 25 deg.c led (backlight unit ) parameter symbol rating unit forward current if 120 ma pulse forward current ifp 200 ma allowable reverse current ir 85 ma power dissipation pd 480 mw dice temperature tj 130 deg.c ifp conditions: pulse width = < 10msec. and duty = < 1/10 note: ta = 25 deg.c ( from nichia?s one led specification ) 4 electrical specification 4.1 dc characteristics specification parameter symbol condition min. typ. max. unit power supply voltage vdd 3.0 3.3 3.6 v logic high level input voltage vih 0.7vdd - vdd v logic low level input voltage vil vss - 0.3vdd v logic high level input current iih vin = vss to vdd ta = 25 deg.c - - 1 ua power supply current idd note 1 - 140 (200) ma power supply current (sleep mode) idd note 2 - 7 (10) ma note 1: typ. vdd=3.3v, ta = 25 deg.c, display : all white max. vdd=3.0v to 3.6v, ta = -30 to +85 deg.c, display : all white note2: vdd=3.3v, ta = 25 deg.c, input pins of hs,vs,pclk,r[5 :0],g[5:0],b[5:0],xcs,scl,sda are being fixed to ?h? or ?l?. note3: vss= 0 [v] data modul ag - www.data-modul.com 18 product number L5S30978p00 revision number 01 page epson imaging devices corp. 4.2 characteristics of led and led driving value item min. typ. max. unit forward current (if ) - 80 ma forward voltage (vf) at if=80ma (3.6) 4.0 v life time (note 2 ) - 60,000 hr number of led components 24 pcs. / one lcd module note 1: ta = 25 deg.c ( from nichia?s one led specification ) note 2: a reference mention (from nichia?s technical information) this is presumption of life time. it is not a performance guarantee. note 3: ambient temperature vs. forward vo ltage ( from nichia?s one led specification ) note 4: [reference ambient temperature vs. allowable forward current for tft module it is a derating curve in a module simple substance. " n c j f o u 5 f n q f s b u v s f w t " m m p x b c m c m f ' p s x b s e $ v s s f o u 5 b * ' g p s 5 ' 5 n p e v m f " n c j f o u 5 f n q f s b u v s f < 5 b > e f h $ " m m p x b c m f ' p s x b s e $ v s s f o u < * ' > n " n b yy * ' 3 f d p n n f o e b u j p o data modul ag - www.data-modul.com 19 product number L5S30978p00 revision number 01 page epson imaging devices corp. 4.3 ac characteristics 4.3.1 rgb interface 4.3.1.1 vertical timi ng of rgb interface ta = -30 - +85 deg.c, vdd = 3.0 ? 3.6 v, vss = 0 v item symbol condition min. typ. max. unit vertical cycle vp 525 525 525 line vertical low pulse width vsw 2 2 2 line vertical front porch vfp 13 13 13 line vertical back porch vbp 30 30 30 line vertical active area vdisp 480 480 480 line note1: signal rise and fall times should be equal or less than 3 ns. note2: logic high and low levels of input signals are specified as 0.3 x vdd for low state and 0.7 x vdd for high state. note3: data lines can be high or low during blanking time. note4: vp, vsw, vfp, vbp and vdisp are fixed to one value. note5: vp, vsw, vfp, vbp and vdisp are counted by the next falling of hs after transition of vs. vs r(5:0) g(5:0) b(5:0) note3 note3 hs vp vdisp vbp vfp vsw data modul ag - www.data-modul.com 20 product number L5S30978p00 revision number 01 page epson imaging devices corp. 4.3.1.2 horizontal timi ng of rgb interface ta = -30 - +85 deg.c, vdd = 3.0 ? 3.6 v, vss = 0 v item symbol conditions min. typ. max. unit horizontal cycle hp note 3 1048 1048 1048 dot horizontal low pulse width hsw 13 13 13 dot horizontal back porch hbp 203 203 203 dot horizontal front porch hfp 32 32 32 dot horizontal active area hdisp 800 800 800 dot tpclk 28.9 30.3 33.6 ns pixel clock frequency when rgb is running fpclk 29.7 33.0 34.6 mhz note1: signal rise and fall times are equal or less than 3ns. note2: logic high and low levels of input signals ar e specified as 0.3 x vdd for low state and 0.7 x vdd for high state. note3: data lines can be high or low during blanking time. note4: hp, hsw, hfp, hbp and hdisp are fixed to one value. hs r(5:0) g(5:0) b(5:0) note3 note3 pclk hp hdisp hbp hfp hsw tpclk data modul ag - www.data-modul.com 21 product number L5S30978p00 revision number 01 page epson imaging devices corp. 4.3.1.3 general timing of rgb interface vs hs pclk vsht vsst hsst pclklt pclkcyc hsht pclkht dst dht data ta = -30 - +85 deg.c, vdd = 3.0 ? 3.6 v, vss = 0 v item symbol condition min. typ. max. unit vs setup time vsst 8 - - ns vs hold time vsht 8 - - ns hs setup time hsst 8 - - ns hs hold time hsht 8 - - ns pixel clock cycle when rgb interface is running pclkcy c 28.9 30.3 33.6 ns pixel clock low time pclklt 12 13 - ns pixel clock high time pclkht 12 13 - ns data setup time dst 8 - - ns data hold time dht 8 - - ns note1: signal rise and fall times should be equal or less than 3ns. note2: logic high and low levels of input signals ar e specified as 0.3 x vdd for low state and 0.7 x vdd for high state. data modul ag - www.data-modul.com 22 product number L5S30978p00 revision number 01 page epson imaging devices corp. 4.3.2 serial interface ta = -30 - +85 deg.c, vdd = 3.0 ? 3.6 v, vss = 0 v item symbol condition min. typ. max. unit serial clock cycle tscyc 160 - - ns scl high pulse width tshw 65 - - ns scl low pulse width tslw 65 - - ns data setup time (write) tsds 40 - - ns write mode data hold time tsdh 40 - - ns xcs high pulse width tchw 60 - - ns tcss 60 - - ns xcs? scl time tcsh 60 - - ns note 1: the output signal?s rise and fall times are to be stipulated maximum 15 ns. note 2: the input signals? rise and fall times should be equal or less than 15 ns. note 3: logic high and low levels of input signals are specified as 0.3 x vdd for low state and 0.7 x vdd for high state. note 4: please use the level shifter not voltage divider (drop by resistor ) if customer need to change the voltage level. if customer uses the voltage divi der, we can not guarantee the serial function. tcss xcs scl sda tcsh tchw tscyc tslw tsdh tshw tsds tf tr data modul ag - www.data-modul.com 23 product number L5S30978p00 revision number 01 page epson imaging devices corp. 4.3.3 reset timing display statu s xres normal operation resetting initial condition (default for hw reset) trw trt symbol parameter min max unit trw reset pulse width 10 us 5 (note 1) ms trt reset cancel time 120 (note 2) ms * it is necessary to wait trt afte r releasing xres before sending commands. note 1: when reset applied during sleep mode. note 2: when reset applied during display on mode. note3: signal rise and fall times are equal or less than 15 ns. note4: logic high and low levels of input signals ar e specified as 0.3 x vdd for low state and 0.7 x vdd for high state. note5: during the resetting period, the display will be blanked (black display) immediately and then return to default condition for hardware reset. data modul ag - www.data-modul.com 24 product number L5S30978p00 revision number 01 page epson imaging devices corp. 4.4 power modes 4.4.1 display on mode in this mode, the display is able to show maxi mum 262 144 color from rgb interface. pclk, hs and vs are always activated by the host. image data from rgb interface is displayed on panel. 4.4.2 sleep mode in this mode, the dc/dc converter in the lcd drivers and panel driver circuit are stopped. display is blank and not any abnormal visual effect on the display. 4.4.3 power off in this mode, vdd is able to be removed. 4.4.4 state transition di agram of power modes display on mode power off power on sequence power off sequence power off se q uence slpout se q uence sleep mode slpin se q uence data modul ag - www.data-modul.com 25 product number L5S30978p00 revision number 01 page epson imaging devices corp. 4.5 power functions 4.5.1 power on and off sequences 4.5.1.1 power on sequence power-up auto-refresh forced to on slpout dispon vdd xres *3) *1) this relationship must be kept. *2) rgb signal should be started before xres signal is inputted. *3) these commands may not be sent. rgb-i/f 3 line serial if xcs vdd min. 0-11h 5ms min. 0-29h 100ms min. *1): 20s min. 0-d0h, 1-03h, 0-c0h, 1-11h, 1-11h, 1-01h forced auto - refresh - on *2) 0.3 x vdd 0.7 x vdd 4.5.1.2 power off sequence vdd min 0ms min 0ms xres 0.7xvdd vss 3 line serial if rgb signals slpin(10h) min 50 ms valid data vdd min. = 3.0v data modul ag - www.data-modul.com 26 product number L5S30978p00 revision number 01 page epson imaging devices corp. 4.5.2 interval of power on and power off vdd min 100ms please refer to power on and off sequences about other signals timing. 4.5.3sleep in and sleep out sequence "on" vdd "h" xres min 100ms min 20 ms min 50 ms min 50 ms min 100ms 3 line serial if rgb signals slpin (10h) disoff (28h) slpout (11h) valid data valid data dison (29h) data modul ag - www.data-modul.com 27 product number L5S30978p00 revision number 01 page epson imaging devices corp. 4.6 recommended sequence 4.6.1 power on sequence 1 p x f s 0 / 7 % % 0 / ? 9 3 & 4 - ? 8 b j u . p s f u i b o v t f d ? 9 3 & 4 ) ? 8 b j u . p s f u i b o n t f d ? " v u p 3 f g s f t i $ 0 . % i 1 i $ 0 . $ i 1 i 1 i 1 i ? 4 - 1 0 6 5 $ 0 . i ? 8 b j u n p s f u i b o n t f d ? % * 4 0 / $ 0 . i refer to 4.5.1.1 for details. 4.6.2 power off sequence 4 - 1 * / $ 0 . i ? 8 b j u . p s f u i b o n t f d ? 9 3 & 4 - ? 3 ( # t j h o b m 0 ' ' ? 1 p x f s 0 ' ' 7 % % 0 ' ' refer to 4.5.1.12 for details. data modul ag - www.data-modul.com 28 product number L5S30978p00 revision number 01 page epson imaging devices corp. 4.6.3 seep in sequence ? 4 - 1 * / $ 0 . i ? 8 b j u . p s f u i b o n t f d ? % * 4 0 ' ' $ 0 . i ? 8 b j u . p s f u i b o n t f d ? 3 ( # t j h o b m 0 ' ' j g o f f e f e ? % * 4 1 - " : 0 / . 0 % & 4 - & & 1 . 0 % & refer to 4.5.3 for details. 4.6.4 sleep out sequence < sleep mode ? display on mode.> ? 3 ( # t j o h b m p o ? 8 b j u . p s f u i b o n t f d ? 4 - 1 0 6 5 $ 0 . i ? 8 b j u . p s f u i b o n t f d ? % * 4 0 / $ 0 . i ? % * 4 1 - " : 0 / . 0 % & 4 - & & 1 . 0 % & refer to 4.5.3 for details. < display on mode ? display on mode> ? 4 - 1 0 6 5 $ 0 . i ? 8 b j u . p s f u i b o n t f d ? % * 4 1 - " : 0 / . 0 % & % * 4 1 - " : 0 / . 0 % & data modul ag - www.data-modul.com 29 product number L5S30978p00 revision number 01 page epson imaging devices corp. 4.6.5 refresh sequence the refresh sequence recovers normal displaying w hen the display becomes unexpected status because of temporary external factors like esd, et al. it is recommended to run this sequence periodically at displayin % * 4 0 / $ 0 . i 4 u b s u e j t q m b z j o h 4 - 1 0 6 5 $ 0 . i ? 8 b j u . p s f u i b o n t f d ? $ 0 - . 0 % $ 0 . " i 1 i / 0 3 0 / $ 0 . i % * 4 0 / $ 0 . i 3 f q f b u u i j t t f r v f o d f data modul ag - www.data-modul.com 30 product number L5S30978p00 revision number 01 page epson imaging devices corp. 5 optical specification 5.1 optical characteristics ta=25deg. c ratings parameters condition symbol min. typ. max. unit remarks contrast ratio = 0 deg. cr 400 700 - - note 1, 4, 5 response time = 0 deg. tr + tf - 30 40 msec. note 1, 3, 5 brightness = 0 deg. b 450 650 - cd/m 2 note 1, 5 ntsc ratio = 0 deg. - 50 56 - % note 1, 5 b 70 80 - r 70 80 - t 70 80 - viewing angle cr? 100 l 70 80 - deg note 1, 2, 4, 5 luminance homogeneity max brightness u 75 80 % note 1, 7 max brightness wx note.8 0.332 note.8 - note 1, 5 white chromaticity max brightness wy note.8 0.348 note.8 - note 1, 5 max brightness rx 0.570 0.607 0.644 - note 1, 5 red chromaticity max brightness ry 0.318 0.342 0.365 - note 1, 5 max brightness gx 0.292 0.326 0.360 - note 1, 5 green chromaticity max brightness gy 0.524 0.568 0.612 - note 1, 5 max brightness bx 0.132 0.161 0.190 - note 1, 5 blue chromaticity max brightness by 0.054 0.093 0.132 - note 1, 5 5.2 definition and condition of optical characteristics note1) measurement condition (1) measurement equipment: dms 301 / dms 803 (2) ambient temperature ta: 25 3 deg. c (3) lcd: all pixels are white, vdd=3.3v, fclk=33mhz, fv=60hz (4) measure after 15 minutes of led warm up. (5) if=320(80x4)ma for led. note 2) definition of viewing angle note 3) response time 90% 10 % t r white data 100 % 0% b black black tf normal( =0deg.) b t top right left display face bottom r l data modul ag - www.data-modul.com 31 product number L5S30978p00 revision number 01 page epson imaging devices corp. note 4) contrast ratio "cr": note 5) these parameters shall be measured at center of active area. (refer to note 6) note 6) measurement points note 7) luminance homogeneity cr = brightness at white brightness at black active area ) q 7 1 vp: total number of vertical pixel hp: total number of horizontal pixel luminance homogeneity = x 100 [%] b min. b max. data modul ag - www.data-modul.com 32 product number L5S30978p00 revision number 01 page epson imaging devices corp. note 8) white chromaticity x i j u f t q f d 0.28 0.30 0.32 0.34 0.36 0.38 0.40 0.25 0.27 0.29 0.31 0.33 0.35 0.37 0.39 y z xy a 0.292 0.328 b 0.292 0.314 c 0.332 0.314 d 0.372 0.370 e 0.372 0.382 f 0.345 0.382 data modul ag - www.data-modul.com 33 product number L5S30978p00 revision number 01 page epson imaging devices corp. 6 inspection standard 6.1 quality standard 6.1.1 standards each lot should satisfy the qua lity standards as shown below. * inspection method: compliant with ansi/asqc z1 .4-1993, normal inspection level ii, inspection by single sampling. * aql defect type aql definition major defects 0.4% accompanied with functional abnormalities minor defects 0.65% out of the range of "5.2 appear ance standards", but no functional abnormalities 6.1.2 lot lot means the unit includes all products delivered to your company at one time. 6.1.3 inspection condition 1) enviromental conditions 1. temperature/humidity condtion : normal temprature (25+- 5 degrees) normal humidity 60+-20%rh 2. iluminance environment : not lighted appearance 800 ? 2000lx lighted appearance : transmissive type 100 ? 400lx semi-transmissive 800 ? 2000lx * some specified patterns : 50lx or the less 2) inspection method : inspection by naked eye inspect the screen by naked eye from a distance of about 30 cm and the angle shall be 30 degrees from the vertical direction to the product. veiwing angle is 30 degrees from the vertical direction as shown in the picture below. 3) drive condition : it is done pur suant to product specification. z x y 30? 30? data modul ag - www.data-modul.com 34 product number L5S30978p00 revision number 01 page epson imaging devices corp. 6.1.4 treatment of other problems if any troubles should occur concerns our products that have been assembled at your company's manufacturing processes, both companies shall jointly investigate and resolve the causes. 6.2 appearance standard 6.2.1 application scope the application scope is limited to the viewing area. the product should be judged non-defective if all defects are outside of the viewing area and do not interfere with product quality or the assembly process. note viewing area = bezel opening area. data modul ag - www.data-modul.com 35 product number L5S30978p00 revision number 01 page epson imaging devices corp. 6.2.2 display appearance standard no. items judgment criteria class 1 abnormal display must not be abnormal function such as not function or not to get normal pattern for input signal, etc. major 2 line defect (open, short) no line defect major 3 dot defect (dot failure) no. item bright dot dark dot total 1 defect in screen 2 5 5 2 combined defect 2 2 distance between dots d d>=5mm the smallest one unit r,g or b is defined as one dot. less than 60 % of one dot area is acceptable. minor 4 dot type defect d = (a + b) / 2 size d (mm) tolerance d =< 0.15 ignored 0.15 < d =< 0.4 3 0.4 < d 0 distance between defects : d d>=5mm minor 5 line type defect (black/ white) length l (mm) width w (mm) tolerance ignored w=<0.05 ignored l =< 10.0 0.05 < w=<0.1 3 0.1 < w dot type defect distance between defects : d d>=5mm minor 6 unevenness display should not be remarkable. minor 7 bubble in minor polarizer d = (a + b) / 2 diameter d(mm) tolerance d =< 0.3 ignored 0.3 < d =< 0.5 3 0.5 < d =< 1.0 1 1.0 < d 0 1 0 ! , 1 0 data modul ag - www.data-modul.com 36 product number L5S30978p00 revision number 01 page epson imaging devices corp. 6.2.3 general appearanc e specifications no. items judgment criteria class 1 different specifications not permitted. major 2 damaged resist on fpc copper patterns on fpc must not be visible. minor 3 circuit pattern must not be peeled or separated from fpc. major 4 conductive refuses no solder refuses or solder balls easily moving. fixed particle which has no functional affect can be ignored. minor 5 dirt should not be prominent. dirt on backside is permitted. minor 6 i/f terminal scratch / dirt should not be prominent. minor 7 plating must not be peeled, no rust and no discoloration. minor 8 soldering defect solder omissions is not permitted at any solder point. solder bridges is not permitted. cold soldering is not permitted. major major minor 9 parts soldering there must be fillet. minor 10 metal frame scratch / discoloration scratch out of viewing area and discoloration shall be ignored. minor 6.3 warranty epson imaging devices corp. warrants this product for a period of 14 months from the date of delivery. we replace or compensate for the defective product whic h is judged as our responsibility within the term of warranty. data modul ag - www.data-modul.com 37 product number L5S30978p00 revision number 01 page epson imaging devices corp. 7 reliability 7.1 standard test item and conditon / method test item test condition confirm method / judgment dry heat operating 85 deg.c (surface temperature of polarizer), 240hr after 240 hours, product will be left in normal temperature and normal humidity for two hours. it should work without fail mechanically and electrically, and standard in 6.2 has to be met. low temperature operating -30 deg.c, 240hr after 240 hours, product will be left in normal temperature and normal humidity for two hours. it should work without fail mechanically and electrically, and standard in 6.2 has to be met. dry heat storage 85 deg.c, 240hr after 240 hours, product will be left in normal temperature and normal humidity for two hours. it should work without fail mechanically and electrically, and standard in 6.2 has to be met. low temperature storage -40 deg.c, 240hr after 240 hours, product will be left in normal temperature and normal humidity for two hours. it should work without fail mechanically and electrically, and standard in 6.2 has to be met. high temperature high humidity operating 60 deg.c, 90%rh, 240hr after 240 hours, product will be left in normal temperature and normal humidity for two hours. it should work without fail mechanically and electrically, and standard in 6.2 has to be met. thermal shock -40 deg.c(30min.) +85 deg.c(30min.),200 cycles after 200 cycles, product will be left in normal temperature and normal humidity for two hours. it should work without fail mechanically and electrically, and standard in 6.2 has to be met. data modul ag - www.data-modul.com 38 product number L5S30978p00 revision number 01 page epson imaging devices corp. vibration (non-operating) vibration frequency: 8~33.3hz | amplitude 1.3mm vibration frequency: 33.3~400hz | acceleration:3g, cycle 15min. direction of xz: 2hr, direction of y: 4hr product should work without fail mechanically and electrically and standard in 6.2 has to be met. impact (non-operating) 100g, 6ms, half sin wave,xyz one time for every direction. product should work without fail mechanically and electrically and standard in 6.2 has to be met. esd (non-operating) conduct discharge 100pf, 1500ohm, 15k panel center 3 times (intervals of 1s) non-operating no abnormality like abnormal display. current consumption should be less than twice of initial value. esd (non-operating) air discharge 100pf, 1500ohm, 15k 4 points to metal frame 3 times for each, (intervals of 1s) non-operating no abnormality like abnormal display. current consumption should be less than twice of initial value. 7.2 failure judgment standard after reliability test, inspection is executed in the normal temperature / humidity environment 1) there should be no remarkable deterioration in display quality and appearance. 2) contrast ratio should be over 50% of initial value. 3) brightness should be over 50% of initial value. 4) there should be no abnormal function. 5) current consumption should be less than twice of initial value. data modul ag - www.data-modul.com 39 product number L5S30978p00 revision number 01 page epson imaging devices corp. 8 packing epson imaging devices corporation make packagi ng as shown below to protect the products from shock and vibration during transportation. data modul ag - www.data-modul.com 40 product number L5S30978p00 revision number 01 page epson imaging devices corp. data modul ag - www.data-modul.com 41 product number L5S30978p00 revision number 01 page epson imaging devices corp. lot label product no. L5S30978p** q?ty lot ** pcs ******** customer product no. epson imaging devices corp. epson?s product number quantity epson?s product lot number data modul ag - www.data-modul.com 42 product number L5S30978p00 revision number 01 page epson imaging devices corp. 9 lcd module usage and precautions 9.1 handling 1) broken glass: be careful to broken glass of display surface. when the display surface is damaged, be careful enough not to cut hands by a piece of glass. the surface of a lcd module is covered by plastic film, and glass is hard to be scattered, but there can be the hur t when touching a broken portion. 2) broken panel: do not touch the liquid which flowed out of a panel. when a panel is damaged, and liquid flow, do not breathe in the liquid or drink it or touch it. when liquid stu ck to a hand or clothes, wipe it off in soap or alcohol immediately, then wash in water. when liquid touched to eyes, wash eyes with washing water more than 15 minutes, and undergo a medical treatment of a doctor. 3) preventing of stain and dust: handle a lcd module as much as possible in a room with a few dusts. in addition, when in acceptance inspection or installing process, wear a finger case or the soft gloves which do not make a dust to prevent stain of display surface of a module. 4) protection film of display surface: remove a protection film of display surface in the late st possible assembly process to prevent from dust or scratch on display surface. 5) wiping off of stain on display surface: when display surface of a lcd module was stained, please wipe it off lightly with clean cotton or soft cloth. 6) water drops on display surface: do not leave the water drops on the display surface. when water drops are stuck on the surface, wipe it off with cotton or soft cloth immediately. display surfac e may change color and get a stain of water. in addition, when water drops flow into the lcd module inside, it may cause a trouble or damage. 7) disassemble or modify of lcd module: do not attempt to disassemble, rework or modify t he lcd module by any means. there is the possibility of electric shock, destruction of electronic parts, scratch on a display surface, or dust passing into a lcd module. and if using disassembled, reworked or modifi ed lcd module, electronic parts might emit smoke or outbreak a fire by dust or malfunction of electroni c parts. a product guarantee becomes not available for a lcd module which disassembled, reworked or modified by the user. 8) countermeasures to static electricity: c-mos lsi and an electronic part of the lcd module inside can be destroyed by static electricity. in order not to apply static electricity to a lcd module, spread a conductive mat to a floor and a work desk. in addition, worker should wear a wrist strap. pa y attention not to apply static electr icity while at work. it is recommended to use anti-static electricity air gun in assembly line for lcd. 9) how to insert the connector: when inserting a fpc or take it off, make attention so that strong external force is not added to a fpc the lcd module. the inside connection of lcd driver can be damaged by a strong external force. when installing a lcd module to a target, make attention not to put these fpc between the case of target and the data modul ag - www.data-modul.com 43 product number L5S30978p00 revision number 01 page epson imaging devices corp. lcd module. a connector of a parent application and an i nput fpc of target should not be inserted slantways or half-ways. and confirm it by all means. when it is not inserted correctly, a circuit and a part might be damaged. 10) handling of fpc: be careful not to pull or damage a fpc. damage of a fpc may cause troubles to the lcd module unit. 9.2 design 1) absolute maximum ratings: follow the absolute maximum ratings specified in this document by all means. the absolute maximum rating is the rating which lcd module must not be violated. when using a lcd module at the condition beyond those, a burning/destruction of electronic parts or a permanent damage of characteristics may be caused. therefore, make appropriate design not to violate the absolute maximum ratings with consideration of environmental temperature, deviation of i nput signals, and electronic parts tolerances. 2) torsion and bending while in the process of installing: make attention that no torsion or bending stress is app lied on a lcd module in the installing process to a target frame. even if the stresses are temporarily, they might be the cause of trouble of a lcd module. 3) preventing of a mechanical shock: be careful not to give a strong mechanical shock such as drops or shocks. there can be a cause of trouble such as a scratch of display surface or a ma lfunction of lcd module. especially when fpc is bent strongly, fpc will be cut and lcd will be broken. 4) preventing of a pressure on display surface: make attention that no strong external force such as pushing strongly on display surface of a lcd module. because there can be a scratch on display surf ace or a cause of trouble of a lcd module. 5) preventing of a scratch on display surface: make attention not to rub or push a display surface of a lcd module by a rigid thing such as tools. in addition, be sure not to put a heavy thing such as a tool on display surface and not to pile up lcd modules each other. a polarizer used for display surface is easy to get a scratch or traces and it might be damaged. 6) installation holes, torsion, bending: epson imaging devices corporation recommends us e of all installation holes shown in this document. in addition, a screw to use should be of proper dimensions according to specifications. in addition, installation portions of a lcd module should be designed not to be applied excess torsion or bending. there might be a display unevenness by application of a stre ss during installation even if the lcd module has an evenness for display itself. 7) power supply sequence: the power supply and the input signals of the users? product unit and the inspecti on circuit, etc., connecting to lcd module, which satisfy the power supply sequence of the recommended operating condition, must be used. 8) power supply circuit protection device: please examine and apply the power supply circuit pr otection device if necessary when the lcd module breaks down in accordance with the use condition. data modul ag - www.data-modul.com 44 product number L5S30978p00 revision number 01 page epson imaging devices corp. 9) recommendation for use of a protection cover and a uv cut filter: epson imaging devices corporation recommends us e of a transparent protection cover on a liquid crystal display aperture to prevent scratch and dust of display surface and invasion of water, when using under a too cruel condition in such as outdoors. furthermore, epson imaging devices corporation recommends use of a u.v. cut filter (cuts 390nm or less wa ve length) when it is exposed to direct rays of the sun for a long time. please consider it so that dew condensation does not occur in the cover. 10) temperature dependence of display: the response (optical response) of display varies wi th temperature. the response becomes slow at low temperature. in addition, brightness and chro maticity vary with temperature, too. 11) dew condensation: in an environment of sudden temperature change, there might be a dew condensation on surface or inside of a lcd module. because it causes a degradation of displa y or malfunction, be sure to make consideration for design that dew condensation does not occur. 12) image sticking: it is recommended to avoid display same image for long te rm in order to prevent causing image sticking. also even at displaying moving image, displaying in tr immed image such as pillar-box or letterbox for long term, or repeated frequently, could cause image sticking due to the characteristics of lcd. displaying in full screen is recommended. interlace driving will cause image sticking on the display. please apply non-interlace driving. in case a image sticking occurred, applying full gray im age may work for recovery of sticking image for some, however if severe image sticking occurred by stationary image for more long stretch of time, this recovery measure does not work please pay a ttention on these notes at designing 13) caution about interlace and frc driving: do not input driving signal which apply different voltage in each frame alternately. these driving may cause abnormal image such as image sticking by dc imbalance. please avoid using following driving method basically. interlace signal (pal, ntsc) and frc (frame rate control) because it is leads inappropriate dc apply to lc, and avoidance method is complicated. the countermeasures written in this sect ion have possibility of some image degradation ? interlace the following driving cause some abnormal display. resize (expand / shrink) of interlace signal source. (50/ 60 fps) complement of interlace signal source ex. display ntsc signal source (480 vertical lines ) is shrank to wqvga (240 vertical lines) lcd. data modul ag - www.data-modul.com 45 product number L5S30978p00 revision number 01 page epson imaging devices corp. progressive data 1 2 3 4 5 odd frame even frame original data frame for transmission of odd number line only (1/60s) frame for transmission of even number line only (1/60s) white black lc a pp lied volta g e vcom average of lc applied voltage dc imbarance time countermeasure following driving method by frame memory in your system improves dc imbalance. 1. store an odd frame data to the frame memory. 2. drive with data in frame memory in steps of 2 frames. it means an even frame data is not used. ? frc also the different voltage is applied to lc in each frame caused by the frame rate control. + display data = odd frame odd frame + - + - - + - + figure 23 frc driving data modul ag - www.data-modul.com 46 product number L5S30978p00 revision number 01 page epson imaging devices corp. 9.3 storage 1) storage and transport: keep a lcd module with a packing form of shipment in a dark room which direct rays of the sun does not irradiate with low temperature, with low humidity, and with no dew condensation. in addition, keep it in an environment with little temperature change because there is the possibility that dew condensation occurs by a sudden temperature change. when dew condensation occurs , it may be a cause of operation abnormality or trouble. the shipping carton must not be stacked up over 2m in height. 2) transport: because the master carton may be damaged or shape transformed by an excessive load applied, store and transport with piled up in lower than the number which recorded in a master carton label. trays are used to package lcd modules for ship ment. if lcd modules scratch the tray during shipment, material of the scratched tray may be left onto lcd modules. in such case, clean up lcd modules after removal from trays. 3) handling: because a lcd module is a product having precision electronic parts (fpc etc.) and glass products, it might be damaged by an excessive shock or a dropping, for example, stress by hand. although a lcd module does protected with master carton, handle it carefully to reduce a shock in transshipping, transporting and loading. 9.4 disposal disposing lcd modules: when disposing lcd modules, consult a company spec ialized in industrial waste treatment which is permitted by the government or the local authority. 9.5 other precautions 1) this product is developed and manufactured for t he usage of general av equipments and is not suitable for devices that require high reliability and safety (a ircraft/space use equipments, nuclear control apparatus, life maintenance equipments, etc). 2) use this product correctly according to the operati ng conditions and precautions that are stated in this specification. design carefully to prevent accidents, fire hazards, and social damage because of this product. 3) radiation proof design is not applied to this product. 4) contents in this specification shall not guarantee any third party's intellectual pr operty right or concession of other rights. epson imaging devices corporatio n will not take responsibility for the industrial property issue arising between the user and a third party. 5) this specification includes copyright -related contents. it is strictly prohibited to make partial/full reprints or duplicate copies of this specification without t he approval of epson imaging devices corporation. 6) damages caused by the using beyond conditions or notices or precautions as mentions in this specifications, are responsible for the users. 7) the thickness of the lcd module was measured while had suppressed. data modul ag - www.data-modul.com 47 93.75 6.75 10.8 (active area) 174 63 104.4 (active area) 111.75 177.75 mm title design div. a3 rev.3.0 product no. 9 8 7 6 5 4 3 2 discussed or reproduced in whole or in part without epson imaging devices's consent. discussed or reproduced in whole or in part without epson imaging devices's consent. discussed or reproduced in whole or in part without epson imaging devices's consent. discussed or reproduced in whole or in part without epson imaging devices's consent. a a 2 1 3 1:2 new issue 4 5 6 f e 7 unit designer tol.-angle date 8 d c b L5S30978p00 tol.-size 4 6 dwg no. f 5 mgr 2009/07/09 b c chief design p068887-11-00 outline drawing information enclosed herein shall be kept in strict confidence under a non-disclosure agreement and shall not be used, information enclosed herein shall be kept in strict confidence under a non-disclosure agreement and shall not be used, information enclosed herein shall be kept in strict confidence under a non-disclosure agreement and shall not be used, information enclosed herein shall be kept in strict confidence under a non-disclosure agreement and shall not be used, e * check d the copyrights and proprietary rights for the drawing & design on this print are the property of epson imaging devices corp. the copyrights and proprietary rights for the drawing & design on this print are the property of epson imaging devices corp. the copyrights and proprietary rights for the drawing & design on this print are the property of epson imaging devices corp. the copyrights and proprietary rights for the drawing & design on this print are the property of epson imaging devices corp. 0.5 h.nakamura 2009/07/09 date change reason e scale epson imaging devices corp. confidential proprietary epson imaging devices corp. confidential proprietary epson imaging devices corp. confidential proprietary epson imaging devices corp. confidential proprietary 1 solid works a b 187.5 9.8 (bezel opening) 106.4 (bezel opening) 176 120 5.75 (stiffener) (stiffener) |
Price & Availability of L5S30978
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |